Simple powerbank

Cette page est une version traduite de la page Powerbank simple et la traduction est complétée à 100 %. Participer à la traduction

Prototype de Nomade des Mers | Catégories : Énergie

Nomade des Mers

https://wiki.lowtechlab.org/wiki/Powerbank_simple/en

Dernière modification le 22/10/2019

Difficulté

Facile

Durée

1 heure(s)

Coût

5 EUR (€)

Description

Powerbank / single external battery for small independent lighting or smartphone charging.

Difficulté

Facile

Durée

1 heure(s)

Coût

5 EUR (€)

Autres langues :

Deutsch • ‎English • ‎español • ‎français • ‎العربية • ‎فارسی

Sommaire

1 Description
2 Sommaire
3 Introduction
4 Étape 1 - Selection of lithium-ion cells
5 Étape 2 - Assembly of components.
6 Étape 3 - Put in the container.
7 Étape 4 - Use
8 Notes et références
9 Commentaires

Licence : Attribution-ShareAlike (CC BY-SA)

en fr 1

Introduction

This tutorial presents the manufacture of a very simple powerbank allowing the feeding of a small lighting or the charging of a smartphone via a USB socket. It is made from lithium-ion cells recovered from used laptop batteries.

Safety :

Lithium-ion batteries can be particularly dangerous. Their charges and discharges must be protected with a suitable electronic circuit. In addition, short circuiting a cell can cause it to explode: It is therefore imperative to handle them with care: gloves and goggles.

Laptop batteries:

Removable computer batteries are mostly made up of lithium-ion cells in series or parallel with an input charge / discharge regulator. When a battery is faulty, it is very likely that only one of the cells or even just the regulator fails. It is still possible to reuse the others.

Why reuse this type of cells / batteries?

Storage: This type of technology is currently one of the lightest compared to the amount of energy it can store.

Environment: 1300T of accumulators are thrown away each year with a forecast at 14000T for 2020. Depending on the country, they end up either in nature, rejecting toxic substances, or part of them for energy-consuming recycling. However, many of the cells are potentially usable as is for a new life.

Economy: Small local economies can arise from the reuse of lithium-ion cells still usable, for the production of lamps, powerbanks, etc.

Technical data :

The realization of a powerbank from lithium-ion cells requires cell recovery as well as the acquisition of an electronic module charge / discharge. 2 options are available later:

The simplest option (explained in this tutorial) is the use of a single lithium-ion cell. This option requires only to validate the proper functioning of the cell by a voltage test.

The second option is to couple several cells together according to their load capacity. This requires more complex manipulation available ici.

Matériaux

A used laptop battery.
A "lithium-ion battery holder", if possible with wire.
A load / unload module.
Tin wire.
A container for the components: here plastic tube / inner tube and bottle cap.

Outils

Gloves and goggles.
Chisel / hammer
Wire stripper.
Soldering iron.

Note: Safety equipment is to be worn throughout the realization.

Étape 1 - Selection of lithium-ion cells

Open the computer battery, possibly using the chisel and hammer, while remaining delicate so as not to damage the cells.

Separate the cells.

Note: As a safety measure, pay particular attention to the fact that the "+" and -" of cells never come into contact.

Using a voltmeter measure the voltage across each cell and keep only those above 2.5V.

Notes:

1) The + of the cell is located on the side of the groove on the cell.

2) The minimum voltage reached by a discharged lithium-ion cell is 2.5V. If the voltage is lower, it can go to recycling.

Étape 2 - Assembly of components.

Weld the - of lithium-ion battery holder to + of the charge / discharge module.

Proceed in the same way for the -.

Insert the cell in the "lithium-ion battery holder", respecting the '+' and '-' polarity (at risk of explosion of the cell).

Test the charge and discharge of the cell via usb / mini USB cables: a color code of blue LED (charged) and red (discharged) on the load module allows to know the state of the cell.